hello, i tried it in the german forum first, but i dont think, that someone could help me there, so i try my luck here. i hope its alright. if not, than a mod could maybe delete my thread in the german forum. (thx) so...here we go...i had my raspi3b connected with a alexa switch. so everytime i cut off the power, the pi lose is power completely...thats bad, so i have it now running 24/7h and only my tv, avr and the leds lose the complete power, when i turn it off with my alexa. someone said, that maybe my system is damaged (raspbian jessie), so i formatted my sdcard and started new, but with raspbian stretch lite. there i didnt have luck...hyperion isnt working. so i started again from the beginning, but now with the newest version of raspbian jessie! but it also dont work. and i got exact the same error message how could i fix this problem? tells me this: than i tried this: No journal files were found, is what i get as answer. after that i tried it shows me: im not sure, but should be "1b71:3002" my grabber? i cant remember, but i think i had also a name after that numbers, when hyperion was working. i disconnected than everything....waited about n hour and started up all again. now in hypercon i could grab a picture....so, the grabber seems to work? now i reached the end of my (small) linux knowing...i hope someone can help me with it. if you need more infos, just tell me. info: i attached my configfile of my hyperion setup. maybe it helps? thnaks
Hi, Correct. It should be more like: Bus 002 Device 002: ID 1b71:3002 Fushicai USBTV007 Video Grabber [EasyCAP] It appears that the grabber simple broke. Or perhaps the power supply that powers the Rpi (and the grabber) is lacking. I would make sure it is able output at least 2 amps. Minimum. The usb grabber might have malfunctioned due to lack of sufficient power. If you have a 3+ amps power supply you can try to increases the amperage to the usb ports from the default 600mA to 1+ amp. By adding "max_usb_current=1" to the file "/boot/config.txt". Do not do this if your supply is less then 3 amps, Edit: the "max_usb_current=1" only works on the Rpi 3, and B+, and I think the Rpi model 2. Not Rpi0 or Rpi 1. Hope it's of help.
yea. exactly what i could remember! currently im working. 3hrs to go...when im at home, ill try max_usb_current=1. and first i need to watch the power supply...ok, but i think its the original raspi power supply with that berry on it. i hope the grabber isnt broken it worked all just fine for weeks and now that problem to your edit: i got a raspi 3b. there it should also work. (sorry for my english, but ill give my best ) ill tell you if it worked or not later. thanks
other question....i read here: https://hyperion-project.org/wiki/II-V42L-Grabber-USB-Grabber that: Nonworking grabbers are: Logilink and i have https://www.amazon.de/gp/product/B0013BXFLG/ref=ppx_yo_dt_b_asin_title_o02__o00_s00?ie=UTF8&psc=1 LogiLink Audio und Video Grabber USB 2.0 and it worked. maybe i should instant buy another one? im not sure now
I looked at the link for the grabber. It has good reviews. However it does not specifically say in the description it's a UTV007 chip. Their is another that specifically said it's a UTV007 chip (www.amazon.de/EasyCAP-Grabber-Fushicai-UTV007-Chipsatz/dp/B01FPXCTSM) On a side note. I noticed the usb grabbers run very hot. Some hot enough to make the plastic case pliable. I have attach a heatsink to all usb grabbers I use, just for caution. I have not lost a grabber yet. This is a picture I took a year and a half ago. That grabber is still going today and it's been on 24/7 since that picture. I Hope it helps
ok, i tried now to add usb_max_current=1 to the config, rebooted and typed again lsusb. still the same problem. i really think, that the grabber device is broken. my friend got a working one, so i try it tomorrow and if it works, than ill buy a new one. do you guys have a amazon link? prime delivery? and amazon.de link, for germany would be nice. //edit: i got it working again. it was a broken cable. i fixed it and now it works thanks for help
*push* hello guys, i have again a problem with my hyperion. it stopped working again. last day i watched tv and my odroid stopped working, also the rasperry. i restarted both with my ssh android app. now hyperion doenst work anymore. i used a new sdcard and reinstalled all. tried the old backup config with which it worked before with no problems, and i created after that a new one. nothing... ok, when i type i got this: any ideas? you can see, that my last post was on 28.01.2019. from there till yesterday it all worked fine and now this thanks
hi, today i did a fresh install of hyperion and now its working again. when i use lsusb i can see the grabber again. dont know what was wrong. but okey, now its working fine again. thx
