1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

SOLVED ws2801 does not light

Discussion in 'Hardware Support' started by 2dela, 14 May 2016.

  1. 2dela

    2dela New Member

    Messages:
    2
    Hardware:
    RPi3
    hi,

    i just installed raspbian and openelec both with same result.
    the hyperion service is running in both cases but the led are not lighting as they should be, just some of them are lighting in withe, those led are lighting with the pi with or whiout power, its like the gpio ports 19 and 23 are not seding the right signals.

    the thing is how can i check that those ports are seding what they should send and/or my led are fine hehe

    also i am not able to put the led on with HyperCon

    any help or any advise will be really apreciated

    btw output of my hyperion daemon:
    [email protected]:/etc/ssh# /usr/bin/hyperiond /opt/hyperion/config/hyperion.config.json
    Hyperion Ambilight Deamon
    Version : V1.02.0 (brindosch-f4162eb/2d45d51-1462453507
    Build Time: May 5 2016 06:07:47
    INFO: Selected configuration file: /opt/hyperion/config/hyperion.config.json
    HYPERION INFO: ColorTransform 'default' => [0; 84]
    HYPERION INFO: ColorCorrection 'default' => [0; 84]
    HYPERION INFO: ColorAdjustment 'default' => [0; 84]
    LEDDEVICE INFO: configuration:
    {
    "colorOrder" : "rgb",
    "name" : "MyHyperionConfig",
    "output" : "/dev/spidev0.0",
    "rate" : 250000,
    "type" : "ws2801"
    }

    HYPERION INFO: Not creating any smoothing
    EFFECTENGINE ERROR: Effect directory can not be loaded: /storage/hyperion/effects
    EFFECTENGINE INFO: Initializing Python interpreter
    INFO: Hyperion started and initialised
    INFO: Boot sequence 'X-Mas' EFFECTENGINE INFO: run effect X-Mas on channel 0
    EFFECTENGINE ERROR: effect X-Mas not found
    failed
    INFO: Kodi checker created and started
    INFO: Json server created and started on port 19444
    INFO: Proto server created and started on port 19445
    INFO: Boblight server created and started on port 19333
    DISPMANXGRABBER INFO: Display opened with resolution: 1920x1080
    BLACKBORDER INFO: threshold set to 0 (0)
    BLACKBORDER INFO: mode:default
    INFO: Frame grabber created and started
    KODICHECK INFO: Kodi Connected
     
  2. TPmodding

    TPmodding Administrator Staff Member Administrator

    Messages:
    1,886
    Hardware:
    RPi1/Zero, RPi2, RPi3, +Arduino, +nodeMCU/ESP8266
    May your First led/IC is corrupt...did you try to cut the First led?
     
  3. Rick164

    Rick164 Administrator Staff Member Administrator

    Messages:
    189
    Hardware:
    RPi2, +Arduino, +AtmoOrb
    If they're lighting with or without power you most likely have a wiring problem, would recheck them first and like @TPmodding mentioned can try connecting further along in case a led died :)
     
  4. Brindosch

    Brindosch Active Member

    Messages:
    658
    Hardware:
    RPi1/Zero, RPi2, RPi3, +nodeMCU/ESP8266
    Think it´s strange too, that it can´t load the effect directory.
    You installed Hyperion via HyperCon?
     
  5. 2dela

    2dela New Member

    Messages:
    2
    Hardware:
    RPi3
    hi,
    the issue was with the leds, yesterday night i cut the first led and it worked perfectly,
    thx for all your answer